Guide

Christmas Pottery Ideas: Ornaments, Trees, Mugs and Plates to Make Before the Holidays

Quick answer

Good Christmas pottery ideas are flat slab ornaments, wheel-thrown baubles, small trees, holiday mugs, a cookie plate for Santa and hand-built houses for LED lights. Kiln clay pieces need drying time plus a bisque and a glaze firing, so make them by the third week of November and have them glaze fired by mid December. Air-dry and oven-bake ornaments can be made the week before.

On this page
  1. Plan backward from Christmas
  2. Christmas ornaments
  3. Small Christmas trees
  4. Christmas mugs and cups
  5. Christmas plates and serving pieces
  6. Houses, luminaries and candle holders
  7. Decorating in Christmas colors
  8. Firing ornaments without them sticking
  9. Common mistakes
  10. Safety notes
  11. What you need
  12. Frequently asked questions

Christmas pottery ideas fall into two groups: decorations that hang or stand (ornaments, small trees, houses and luminaries) and pieces that get used at the holiday table (mugs, plates and serving dishes). Most can be made on the wheel or by hand. The part people miss is timing: kiln clay has to dry and go through two firings before it can be wrapped, so Christmas pottery needs to start in November. This guide gives the projects and a backward schedule from December 25.

Research note: project and firing notes come from Ceramic Arts Network's wheel-thrown ornament article, clay and glaze maker pages, and the Christmas project guides that rank for this topic. We describe the methods; we do not claim to have made the pieces. Specs checked October 2026.

Plan backward from Christmas

Drying and firing take longer than making. Use this as a planning estimate for kiln clay, then adjust for your clay, your humidity and your kiln or studio.

WhenKiln clayAir-dry or oven-bake
Early to mid NovemberMake mugs, plates and trees (thicker pieces dry slowest)Plan designs, buy clay
By about November 22Finish ornaments and small piecesNothing yet
Late November to early DecemberDry slowly to bone dry, then bisque fireStart making
Early to mid DecemberUnderglaze, glaze and glaze fireDry, bake, paint and seal
By about December 15Unload, check, wrapFinish and wrap

If a studio fires for you, ask for its holiday cutoff now. Studios batch firings and many stop taking work well before Christmas. For drying stages, see our greenware guide; for firing times, see how long it takes to fire pottery.

Christmas ornaments

Flat slab ornaments

The easiest Christmas pottery project. Roll a slab about 1/4 inch thick, press in a texture (lace, a leaf or a stamp), cut shapes with cookie cutters and push a straw through for the hanging hole before the clay stiffens. Make the hole a little larger than you think, since clay shrinks in firing. Dry flat between boards so the ornaments do not curl. Our pottery ideas for beginners page covers the slab basics.

Wheel-thrown baubles

Ceramic Arts Network describes throwing ornaments off the hump: center a lime-sized amount on top of a 3 to 4 lb ball of clay, open it like a small cup, thin the wall to about 1/8 inch and collar it closed into a hollow sphere. Pierce a tiny hole with a needle tool so air can escape in the bisque firing. The article adds a top made from a textured slab, joined by scoring and slipping, and fits a wire hanger after the glaze firing.

Pinch pot bells and stars

Pinch a small cup, turn it upside down, add a clay loop on top and hang a fired clay bead inside on wire for a clapper. Pinched stars and snowflakes from small slabs work the same way as flat ornaments.

Ornaments without a kiln

Air-dry and oven-bake clay make good ornaments when there is no time or kiln. Sculpey says to bake Original Sculpey at 275°F (130°C) for 15 minutes per 1/4 inch of thickness, in a conventional or toaster oven, never a microwave. Paint air-dry ornaments only once fully dry, then seal them, and keep them indoors.

Small Christmas trees

Wheel-thrown trees

Throw a tall closed cone, or stack two or three thrown rings of decreasing size. Ceramic School's tree project marks the layers while throwing to guide trimming. Carve or pierce holes at leather hard for a light to shine through.

Hand-built slab trees

Roll a slab, cut a half circle and wrap it into a cone, scoring and slipping the seam. Press in branch textures, cut small holes for lights and leave the base open for an LED light. For slip-cast trees in the classic style with plastic bulbs, see our ceramic Christmas tree mold guide.

Put an LED light inside, not a candle, and do not leave any light running unattended.

Christmas mugs and cups

A holiday mug is the most-used piece on this list. Throw or slab-build a cylinder, add a handle shaped like a candy cane or a holly sprig, or carve a pattern through a coat of colored underglaze. A set of small cocoa cups without handles is faster and has less risk of cracking at the handle joint. See our pottery wheel ideas for clay weights.

Food safety: for anything that will hold a drink, use a glaze its maker labels food safe, fire it to the stated cone and test the result. We cannot promise a glaze is food safe on your pots. Our food safe glaze guide explains what the labels mean.

Christmas plates and serving pieces

  • Cookie plate for Santa: drape a slab over a plate form, then write "Cookies for Santa" and the year in underglaze pencil on the bisque. It becomes a family piece used once a year.
  • Tree-shaped serving dish: cut a tree from a slab, raise the edges slightly and press a pine texture in the center.
  • Holly snack bowls: pinch or throw small bowls and add sprigged holly leaves and red berries.
  • Embossed pine plates: press real pine sprigs into a slab, then glaze with a transparent or semi-transparent glaze so the texture shows.

The same food-safety rule applies to plates and bowls.

Houses, luminaries and candle holders

Small slab houses with cut-out windows make a village on a mantel. Cut the walls from one leather-hard slab using a paper template, score and slip the corners, and add a pitched roof that overhangs a little. Cut windows and doors with a fine knife while the clay is still firm enough to hold an edge, and leave the base open or cut a hole in the back for the light. A row of three houses of different heights looks better than one large one.

A wreath-shaped candle holder starts as a thrown or coiled ring with sprigged leaves around it. In kiln-fired clay, a house or wreath can hold a tea light, with the flame kept away from anything that burns. Air-dry and oven-bake clay are not heat safe, so pieces made from them should only ever hold an LED light.

Decorating in Christmas colors

Red and green underglazes are the obvious pick, but fired color can shift with temperature. Mayco, for example, shows fired chips of its Fundamentals underglazes at cone 06, 6 and 10, and some colors deepen at cone 6. Check the maker's fired chip at your cone before you paint a whole batch, and test one piece first. Underglaze pencils are handy for names and dates on ornaments. For a wider choice of colors, see our best underglazes guide.

Firing ornaments without them sticking

  • Keep glaze off the back of flat ornaments, or wax the back, so they can sit directly on the shelf.
  • For ornaments glazed all over, Ceramic Arts Network suggests hanging each one on high-temperature bead wire balanced across kiln posts, with a scrap of clay underneath to catch drips.
  • Keep glaze out of hanging holes so they do not seal shut.
  • Load ornaments with space between them; glazed pieces that touch fuse together.

For the first firing, see our bisque firing guide.

Common mistakes

  • Starting in December. Kiln clay pieces will not be dry and fired in time.
  • Making hanging holes too small. They shrink in drying and firing.
  • Leaving a closed form without an air hole. Trapped air can crack it in the kiln.
  • Drying flat ornaments face up on a table, so the edges curl.
  • Putting a lit candle in air-dry or polymer clay.

Safety notes

Clay dust contains crystalline silica: clean with a damp sponge, never dry sweep, and wear a NIOSH-approved respirator when mixing dry clay or glaze. Read each glaze maker's SDS. Kilns get hot outside and need the clearance and ventilation their maker specifies. Bake polymer clay only as its maker directs, in a ventilated room. Never leave candles or lights unattended.

What you need

Clay, a rolling pin with guide sticks, cookie cutters, a straw for holes, a needle tool, underglazes and a clear glaze in your cone range, plus access to a kiln. Our underglaze guide helps you choose colors. For more gifts to make alongside these, see our clay gift ideas.

Sources: Ceramic Arts Network, Pottery Making Illustrated "Wheel-Thrown Ornaments: Forming an Heirloom from Clay" (wall thickness, air hole, bead wire firing); Mayco Fundamentals underglaze fired color chips; Sculpey Original Sculpey baking instructions; Christmas project guides from Ceramic School, Corrie Bain, Potclays and Gathering Beauty reviewed for topic coverage. Specs checked October 2026.

Frequently asked questions

What are some creative Christmas pottery ideas?

Try wheel-thrown hollow baubles, a stacked thrown tree with holes for an LED light, a cookie plate for Santa with the year written on it, a slab village of small houses, or holly snack bowls with sprigged berries. Each can be made in kiln clay and fired before the holidays if you start in November.

When should I start making Christmas pottery?

Start kiln clay pieces in early to mid November and finish small pieces by about November 22. That leaves time to dry them slowly, bisque fire, glaze and glaze fire by mid December. Air-dry and oven-bake pieces can be made in the first half of December.

How thick should clay Christmas ornaments be?

About 1/4 inch is a common thickness for flat slab ornaments: thick enough not to snap, thin enough to dry evenly and hang lightly. For hollow wheel-thrown baubles, Ceramic Arts Network describes thinning the wall to about 1/8 inch.

Can you make Christmas ornaments on a pottery wheel?

Yes. Throw small hollow forms off the hump, close them into spheres, add a slab or coil top for the hanger and pierce a tiny air hole so they do not crack in the bisque firing. Fit a wire hanger after the glaze firing.

Can you put a real candle in a clay Christmas house?

Only in kiln-fired clay, with the flame kept away from anything that can burn and never left unattended. Air-dry and oven-bake clay are not heat safe, so use an LED light in those.

Researched and written by Muhammad Mustafa

Muhammad Mustafa researches and writes Home Pottery HQ from maker spec sheets, manuals, dealer listings and published studio guidance. He does not claim hands-on testing of products he has not used, and every page names its sources.