Verdict: a tiny, flexible kiln, not a mug kiln
The Skutt Firebox is a good buy if you want to fire cone 6 test tiles, pendants, beads, ornaments and very small cups, and also fuse glass or fire metal clay, from a household outlet. It is a poor buy if you expect to fire a set of mugs or bowls, because the chamber is only 8 x 8 inches across.
This review is research-based. We compared Skutt's product pages, two Skutt operating manuals, Skutt's January 2025 ceramic kiln price list and US dealer listings. We have not fired a Firebox ourselves, and where sources disagree we say so.
For the full Skutt range, including the larger KM kilns, see our Skutt kilns guide.
Skutt Firebox models Skutt lists in November 2026
Skutt's ceramic kiln pages show one Firebox model table with three rows: the Firebox 8x6 LT, the Firebox 8x4 LT and the Firebox 8 MTS. The Firebox 14 sits in Skutt's glass fusing kiln section. Every model is single phase, 115V and 15A with a NEMA 5-15 receptacle, per Skutt.
| Model | Power (Skutt) | Max temperature | Chamber | Ship weight | Main use | Price |
|---|---|---|---|---|---|---|
| Firebox 8x6 LT | 115V, 15A, 1,800 W, NEMA 5-15 | Cone 6, 2,250°F (1,232°C) | 8 x 8 in, 6.5 in deep, 0.22 cu ft | 58 lb | Clay to cone 6, glass, metal clay | Check price |
| Firebox 8x4 LT | 115V, 15A, 1,725 W, NEMA 5-15 | Cone 10, 2,350°F (1,288°C) | 8 x 8 in, 4.5 in deep, 0.2 cu ft | 53 lb | Cone 10 tiles, flat work, glass | Check price |
| Firebox 14 | 115V, 15A, 1,725 W, NEMA 5-15 | Cone 0, 1,700°F (927°C) | 15 x 15 in, 6.5 in deep, 0.8 cu ft | 110 lb | Glass fusing and slumping | Check price |
| Firebox 8 MTS | 115V, 15A, 1,725 W, NEMA 5-15 | 2,000°F (1,093°C), no cone listed | 8 x 8 in, 4.5 in deep, 0.2 cu ft | 53 lb | Glass and metal clay | Dealer order |
Source notes: Skutt's 8x4 LT product page lists 1,725 W, while the older KilnMaster LT version of Skutt's Firebox manual lists 1,800 W for the same model. Skutt gives the 8x4 LT as 0.2 cubic feet; Clay-King lists 0.17. Skutt's product pages call 24 x 19 x 19 inches the shipping size, while Skutt's 2025 price list prints it as the exterior size. Krueger Pottery lists the 8x6 at 6 inches deep and 60 lb; we use Skutt's 6.5 inches and 58 lb.
US dealer listings in November 2026 put the 8x6 LT at roughly $1,000 to $1,500, the 8x4 LT at roughly $1,200 to $1,450 and the Firebox 14 at roughly $1,600 to $1,950. Skutt sells only through authorized distributors, so check the live price with a dealer.
Skutt Firebox electrical: volts, amps, breaker and plug
Skutt rates every Firebox at 115V and 15A and says it plugs into a standard 120V outlet, which must be grounded. The receptacle is a NEMA 5-15, the ordinary three-prong household type. The 8x6 LT draws 1,800 W; the 8x4 LT, 8 MTS and Firebox 14 draw 1,725 W.
The breaker size is not published on Skutt's current Firebox product pages. Skutt's 2011 manual for the older Firebox 8 lists a 20A breaker with #12 copper wire, and Krueger Pottery's Firebox 8x6 listing gives the same 20A and #12 figures. Skutt's manuals say never to run the kiln on an extension cord, and the controller manual takes its cost estimate from the wattage on your kiln's serial nameplate.
These are the maker's and dealers' stated figures. A kiln pulls its full current for hours, so the circuit matters even on a household plug. Have a licensed electrician check or install the circuit and receptacle before the first firing, sized from your kiln's nameplate and local code. Never wire a kiln circuit yourself.
At 1.8 kW, the 8x6 LT uses at most 1.8 kWh for each hour its elements run at full power, so firing cost stays small; the Mini Touchscreen can estimate it once you enter your rate. If you are weighing a 120V kiln against a 240V one, see 120V vs 240V kilns.
Skutt Firebox 8x6 LT: the cone 6 model for pottery
This is the Firebox Skutt markets as "the perfect starter kiln." Skutt rates it to cone 6, 2,250°F (1,232°C), which covers low fire clay, cone 6 stoneware tests, glass fusing and precious metal clay. The chamber is an 8 x 8 inch opening, 6.5 inches deep, about 0.22 cubic feet.
Skutt's contents list is one shelf, three posts and kiln wash. The lid opens past 90 degrees so it stays out of the way while you load, and Skutt says the wood handle stays cool at peak temperature. Skutt lists a UL safety listing. Clay-King lists 2.5 inch brick, and two dealers say it reaches glass fusing temperature in under 20 minutes.
Skutt does not publish a maximum piece size. The shelf, the posts and the 2 inches of clearance the Mini Touchscreen manual asks for around the thermocouple all take room inside that 6.5 inch depth, so measure your pieces before you buy. Small cups, tiles, pendants and ornaments suit it; a full-size mug often will not.
- Power: 115V, 15A, 1,800 W, NEMA 5-15 (Skutt)
- Breaker: not published on Skutt's product page; 20A with #12 wire in Skutt's older Firebox 8 manual and Krueger Pottery's listing
- Max temperature: cone 6, 2,250°F (1,232°C)
- Chamber: 8 x 8 in opening, 6.5 in deep, 0.22 cu ft
- Controller: Mini Touchscreen
- Included: shelf, three posts, kiln wash
- Ship weight: 58 lb
Pros
- Household 120V plug
- Cone 6 rating
- Clay, glass and metal clay modes in one controller
- Lid and cool handle make loading easy
Cons
- Very small chamber
- Cone 6 ceiling leaves no headroom above cone 6
- Breaker not printed on the current product page
Who should skip it: Anyone who wants to fire finished mugs and bowls in batches, or cone 10 glazes; see the larger options in our small kiln picks.
Skutt Firebox 8x4 LT: cone 10 in a shallower chamber
The 8x4 LT trades depth for heat. Skutt rates it to cone 10, 2,350°F (1,288°C), with the same 8 x 8 inch opening, the same plug and the same controller, but a chamber only 4.5 inches deep. It draws 1,725 W on Skutt's product page and ships at 53 lb.
That depth suits cone 10 test tiles, flat pendants, buttons and glass, and not much else in clay. One more inconsistency to know: the "Chamber Capacity" block on Skutt's 8x4 LT page repeats the 8x6 figure of 6.5 inches, while the model table on the same page says 4.5 inches. We use 4.5 inches, which matches Clay-King's listing and the model name.
- Power: 115V, 15A, 1,725 W, NEMA 5-15 (Skutt product page; 1,800 W in the older LT manual)
- Max temperature: cone 10, 2,350°F (1,288°C)
- Chamber: 8 x 8 in opening, 4.5 in deep, 0.2 cu ft (Skutt) or 0.17 cu ft (Clay-King)
- Controller: Mini Touchscreen
- Ship weight: 53 lb
Pros
- Cone 10 on a household plug
- Same controller and modes as the 8x6 LT
- Lighter
Cons
- 4.5 inch depth rules out most cups
- Conflicting volume and depth figures across Skutt's own page
Who should skip it: Cone 6 potters, who get more usable height from the 8x6 LT, and anyone who wants taller cone 10 tests.
Firebox 14 and Firebox 8 MTS: glass kilns, not pottery kilns
The Firebox 14 has a 15 x 15 inch opening, 6.5 inches deep, 0.8 cubic feet. Skutt says it holds up to one square foot of tile or a 12 inch square plate, with room for slump molds up to 4 inches deep. It ships with a kiln stand and stand feet at 110 lb.
Its limit is heat. Skutt rates it to cone 0, 1,700°F (927°C), which is below the cone 06 to 04 range most potters bisque fire at (see our cone chart), so it cannot bisque or glaze fire ordinary pottery. It is a glass fusing and slumping kiln with the same Mini Touchscreen controller.
- Power: 115V, 15A, 1,725 W, NEMA 5-15 (Skutt)
- Max temperature: cone 0, 1,700°F (927°C)
- Chamber: 15 x 15 in opening, 6.5 in deep, 0.8 cu ft
- Included: kiln stand and stand feet
Pros
- Wide chamber for plates and tiles on a household plug
- Stand included
Cons
- Not hot enough for pottery
- Heaviest Firebox to move
Who should skip it: Anyone buying a kiln for clay.
Firebox 8 MTS
The Firebox 8 MTS appears only as a row in Skutt's Firebox model table: 115V, 15A, 1,725 W, 2,000°F (1,093°C), an 8 x 8 inch opening and 4.5 inches deep. Skutt lists no cone for it and we found no separate product page, so we would not plan pottery around it.
The Mini Touchscreen controller
Skutt fits every current Firebox with its Mini Touchscreen controller. Skutt's controller manual, revised August 2024, lists these modes:
- ConeFire: pick a cone from 022 to 10 and one of four speeds (fast, medium, medium slow, slow), plus an optional hold.
- GlassFire: pick the firing type, speed and glass COE.
- PMC and Heat Treat: preset programs for precious metal clay and metal work.
- Library: presets such as crystalline glaze, lost wax and bottle slumping.
- Custom: 30 programs of your own. Skutt's product page says 8 ramp and hold segments each; the 2024 manual says up to 16.
During a firing you can Add Time, Add Temp or Anneal Now. The manual also describes 2.4 GHz WiFi for firmware updates and Skutt's KilnLink app, although the Firebox product pages do not list KilnLink as a feature. Skutt is clear that the controller is not a safety device, so stay with the kiln while it fires. Our kiln controller guide explains ramp, hold and cone programs in general.
Placement, clearance and ventilation per Skutt
A small kiln still gets hot on the outside. Skutt's manuals set these rules:
- Keep at least 18 inches (46 cm) between the kiln and walls, shelving and other kilns, on all sides.
- Set it on a noncombustible surface such as bare cement or ceramic tile. Skutt's LT manual cites the Uniform Mechanical Code: without one, use 2 inches of masonry under the kiln, reaching at least 12 inches past its outside edge.
- Install it in a dry, well ventilated, sheltered area such as a garage, carport, utility room or hobby room, away from stored flammables.
- Never fire it inside a cabinet or closet (Skutt's Firebox 8 manual).
- Do not fire when the room is 32°F (0°C) or colder, and watch that a small room stays at or below 100°F (38°C).
- Keep it out of a 10 foot (3 m) radius below fire sprinkler heads, or contact Skutt first.
- Keep a fire extinguisher rated for electrical fires nearby, and keep children and pets away while it fires.
On ventilation, Skutt's LT manual calls it essential for a healthy workspace and tells owners to consult a qualified HVAC professional. Skutt's product page lists no vent accessory for the Firebox. Glaze binders, wax resist and glass glues all smoke early in a firing, so read our kiln vent guide before you choose a room. For viewing the chamber, Skutt's Firebox 8 manual calls for #3 green or gray IR and UV protective glasses, and gloves when opening the lid.
What the Skutt Firebox does well
- Household power: a standard grounded 5-15 outlet, with no 240V circuit needed.
- Three crafts in one kiln: cone, glass and metal clay modes built into the controller.
- Easy loading: a lid that opens past 90 degrees and a handle Skutt says stays cool.
- Warranty terms: Skutt says its warranty covers parts and labor and is never pro-rated.
Weak points to know before you buy
- Size: an 8 x 8 inch chamber holds tiles and small pieces, not a load of mugs.
- Headroom: the 8x6 LT is rated exactly to cone 6, so cone 6 firings run it at its maximum every time.
- Missing figures: no breaker size on the current product pages, and conflicting depth, wattage and segment counts across Skutt's own documents.
- Warranty detail: the product page gives no length. Skutt's LT manual says two years, Clay-King says thermocouples are excluded and Krueger Pottery says elements are excluded, so ask your dealer.
- No upgrades: Skutt's page says no accessories or upgrades are available for the Firebox.
Who should buy a Skutt Firebox kiln, and who should skip it
Buy one if you mostly make small work (jewelry, tiles, ornaments, test tiles), you want glass fusing or metal clay as well, or you need cone 6 tests at home before sending full loads to a community studio kiln.
Skip it if you throw mugs, bowls or plates and want to fire them yourself, or you fire cone 10 pieces taller than a few inches. The alternatives below hold more.
Buying a used Skutt Firebox
Used Firebox kilns come in older versions. Earlier 8x6 LT and 8x4 LT units used Skutt's three-button KilnMaster LT controller, which stores 5 custom programs of 8 segments with cone, glass, PMC and ramp and hold modes. The older Firebox 8, covered by a 2011 Skutt manual, used an Infinite Switch and a digital pyrometer and reaches 2,000°F (1,093°C); it is a glass kiln and does not appear on Skutt's current pages.
Before buying, read the serial plate for the rated temperature, ask for the manual and check the brick, lid and cord. Have a Skutt distributor or kiln technician check the elements and thermocouple; never open the control box yourself.
Alternatives to the Skutt Firebox
- Paragon Caldera: another household-plug mini kiln, rated to cone 10 with a slightly deeper chamber. See our Paragon Caldera review.
- Skutt KM-614-3: 120V on a 20A circuit with a NEMA 5-20 receptacle, cone 6, and an 11 x 11 inch chamber 13.5 inches deep per Skutt. Covered in our Skutt kilns guide.
- Skutt GlazeTech and other test kilns: for frequent glaze testing, a wider 240V tester holds many more tiles; compare options in our test kiln guide.
- Paragon Xpress Q-11A: a small cone 10 kiln with a front door; see front loading kilns.
Sources: Skutt product pages for the Firebox 8x6 LT, Firebox 8x4 LT (with the Firebox 8 MTS model row) and Firebox 14; Skutt Home Studio and Firebox page; Skutt Ceramic Kiln and Accessories Price List effective January 15, 2025; Skutt Mini Touchscreen Controller Operating Manual, revised 8/20/2024; Skutt FireBox 8x6 LT user manual (KilnMaster LT version); Skutt FireBox 8 user manual, revised 6/14/11; dealer listings at Clay-King (8x6, 8x4 LT, Firebox 14), Krueger Pottery (8x6), Blick and The Ceramic Shop (8x6, 8x4). Specs checked November 2026.