Guide

Slip Trailing: Bottles, Tips, Slip Consistency and Technique

Quick answer

Slip trailing is decorating pottery by squeezing lines and dots of liquid clay slip from a soft bottle or bulb with a fine tip. It is usually done on leather hard clay, with slip made from the same clay body and screened smooth so it does not clog the tip. The lines stand up from the surface, survive firing, and can be glazed over or left bare.

On this page
  1. What slip trailing is
  2. When to slip trail: the right clay stage
  3. Slip trailer bottles and tips
  4. How to prepare slip for slip trailing
  5. Colored slip basics
  6. How to slip trail, step by step
  7. Slip trailing patterns to start with
  8. Slip trailers to buy
  9. Glazing and firing slip-trailed pots
  10. Common slip trailing problems
  11. Cleanup and safety
  12. What you need
  13. Frequently asked questions

Slip trailing uses a squeeze bottle like a cake decorator's piping bag. You fill a soft bottle or rubber bulb with slip, fit a narrow tip, and draw raised lines, dots and patterns onto a pot. Because the decoration is clay on clay, it shrinks with the pot and fires into it, and it stays put in the glaze firing instead of running.

This guide is research-based: we compared maker and dealer product pages and published potter guides, listed in the Sources line.

What slip trailing is

Slip is clay mixed with water to a liquid (our slip clay guide explains the types). Trailing is one way of applying decorating slip, alongside brushing, dipping, sgraffito and inlay. It has a long history in slipware, where potters trailed light slip over darker clay for bold lines and dots. Tile makers use a close relative called tube lining, where raised slip lines make little walls that hold separate glaze colors.

When to slip trail: the right clay stage

Most potters trail on leather hard clay, the stage where a pot is firm enough to handle but still damp. Ceramic Arts Network's beginner primer says slips are usually applied at leather hard, though some can go on bone dry clay or bisque.

  • Too wet: the weight and water of the slip can soften a thin piece. A Pottery Making Illustrated plate demonstration warns that slip on wet clay can make the piece collapse.
  • Leather hard: the target. The slip and the pot are close enough in moisture to shrink together.
  • Too dry: a regular slip shrinks while the bone dry pot does not, so lines can crack and flake off. Slips formulated for dry clay or bisque, often sold as engobes, are the exception; follow the label.

Test the stage you plan to use. Ceramic Arts Network suggests trailing test tiles at wet, leather hard and dry stages to learn your slip's range.

Slip trailer bottles and tips

A slip trailer is any soft container that pushes slip out through a narrow opening when you squeeze it. Three types are common.

Plastic squeeze bottles

Soft polyethylene bottles with a nozzle or screw-on tip are the cheapest option and the easiest to refill. The Kemper 4 oz bottle comes with a round tip and a ribbon tip, each with a cap.

Rubber bulbs with metal tips

A soft rubber bulb fitted with a stainless needle tip gives the finest, most even line. Xiem's Precision Applicator is the best-known US example, sold in 1 oz and 3 oz sizes with four interchangeable tips and cleaning pins.

Improvised trailers

Kitchen condiment bottles, empty glue bottles and bulb syringes all work as starter trailers. Cut the opening small at first; you can always enlarge it.

Tip sizes

Needle tips are sold by gauge. A lower gauge number means a larger opening and a thicker line. These are the openings Hot Clay lists for Xiem's tips:

GaugeOpeningComes withTypical use
142.032 mm3 oz setBold lines, thick slip
151.829 mm1 oz setBold lines
161.626 mm3 oz setGeneral slip trailing
171.422 mm1 oz setMedium lines
181.219 mm3 oz setFiner slip lines, underglaze
191.016 mm1 oz setFine lines
200.914 mm3 oz setFine detail, thin slip
210.813 mm1 oz setFinest detail

The Pottery Making Illustrated plate demonstration used a 16 gauge tip for slip and an 18 gauge tip for underglaze, which is a sensible starting pair.

How to prepare slip for slip trailing

Make trailing slip from the same clay body as the pot, or one with a matching shrinkage, so the lines stay attached. Soak dry scraps in water until they slake down, mix, then screen the slip through a fine sieve to remove grog and lumps. Lumps are the main cause of clogged tips.

Published guidance on thickness differs. Meesh Pottery describes a thick, yogurt-like slip so lines hold their shape, while the Pottery Making Illustrated porcelain demonstration describes slip that flows like a thin batter. Both are right for their effect: thicker slip gives raised, rounded lines; thinner slip gives flatter lines that settle into the surface and suit fine tips. Mix a little of each and trail test lines on a leather hard slab before you commit to a pot.

Stir the slip and let bubbles rise before filling. After filling, tap the bottle and squeeze a little onto scrap clay so the first line does not start with a burst of air.

Colored slip basics

Colored slip starts with a white or light clay slip and adds commercial ceramic stains or metal oxides. Stains such as Mason stains are usually used at higher percentages in slip than in glaze, because the color sits in an opaque clay layer; our Mason stains guide gives the published starting ranges. Always fire a test tile, because colors change with your clay, cone and glaze.

Glaze choice can shift a slip color. Ceramic Arts Network warns that pinks, lavenders and purples need a zinc-free glaze over them, or the color will shift. How colored slip compares with commercial underglaze for decoration is covered in our planned guide to colored slip vs underglaze.

Dry stains, oxides and clay powders are dusty. Mix them with a NIOSH-approved respirator, read each product's SDS, and clean spills with a wet sponge, never a broom.

How to slip trail, step by step

  1. Practice first. Trail lines and dots on a leather hard slab or the bottom of a bat until the pressure feels even.
  2. Fill the trailer. Remove the tip, squeeze the bottle, dip the opening in the slip and release so slip is drawn in. Replace the tip and tap out air.
  3. Check the pot. It should be leather hard, clean and free of dust. Sketch guide lines lightly with a needle tool if you like.
  4. Hold the tip close. Keep the tip just above the surface or touching lightly, and squeeze with steady pressure.
  5. Move in the right direction. Drag the tip away from its open end so slip trails behind it. Ceramic Arts Network notes that pushing the other way makes the tip dig into the clay and clog.
  6. Keep the bottle full. A nearly empty bottle spits air. Top it up often.
  7. Fix mistakes right away. Lift a wrong line with a damp, thin brush or a wooden tool while the slip is wet, or let it firm up and scrape it off cleanly.
  8. Dry slowly. Cover the pot loosely with plastic so the slip and the pot dry together.

Slip trailing patterns to start with

  • Dots: rows of dots around a rim or a grid of dots on a tile are the easiest way to learn pressure.
  • Banded lines: center a plate or bowl on a banding wheel and hold the trailer still while the pot turns to draw even rings.
  • Chained ovals and loops: the Pottery Making Illustrated plate demo builds a pattern from chained ovals in offset rows, then crosses rows at an angle.
  • Lettering and outlines: fine tips handle names, dates and outlines that you fill with glaze later.
  • Trailing into wet slip: traditional slipware trails lines onto a freshly poured background slip, then drags a fine point through the lines to feather them, or tilts the piece so they swirl.

Trailing combines well with other surfaces: trailed lines over a sgraffito panel, or trailed borders around inlaid areas in mishima.

Slip trailers to buy

These are the trailers we found on US maker and dealer pages. Prices are typical dealer bands in November 2026; check the live price.

Xiem Precision Applicator, 3 oz

Best for fine linesXiem Tools Precision Applicator Set, 3 oz
Key specs 3 oz (85 ml) rubber bulb; 14, 16, 18, 20 gauge tips; 2 cleaning pins
Mid-range tierCheck price on Amazon

The soft rubber bulb is easy to squeeze steadily, and the tips swap in seconds. The dealer listings describe it for slip trailing, glazing, wax resist and fine detail.

  • Capacity: 3 oz (85 ml); 1 oz set also sold
  • Tips: 14, 16, 18 and 20 gauge, plus 2 cleaning pins
  • Build: soft rubber bulb, nickel-plated connector
  • Price band: about $20 to $30

Pros

  • Fine, even lines
  • Four tips included
  • Spare tips sold separately

Cons

  • Costs several times a plastic bottle
  • Fine tips clog with unscreened slip

Who should skip it: potters who only want bold lines and dots, where a plastic bottle is enough.

Kemper 4 oz Slip Trail Bottle

Best budget trailerKemper Tools 4 oz Slip Trail Bottle
Key specs 4 oz polyethylene bottle; round and ribbon tips with caps

A plain polyethylene squeeze bottle with two tips. The Ceramic Shop lists it for slips, underglazes, engobes, glazes and wax resist.

  • Capacity: 4 oz
  • Tips: one round, one ribbon, each with a cap
  • Material: soft polyethylene
  • Price band: about $4 to $8

Pros

  • Low price
  • Holds enough slip for a full pot
  • Ribbon tip makes flat bands

Cons

  • Thicker lines than a needle tip
  • Tip gauge not published

Who should skip it: anyone planning fine lettering or detailed line work.

Mayco Designer Liner (underglaze in a bottle)

Ready-made colored linesMayco Designer Liner underglaze with metal writer tip
Key specs Cone 06 to 10; 10 colors; metal writer tip

If you want trailed color without mixing slip, Mayco's Designer Liner is an underglaze sold in a squeeze bottle with a metal writer tip, rated by Mayco for cone 06 to 10. It is not a slip, so it behaves like underglaze; our Designer Liner review covers it in full.

Pros

  • No mixing
  • Fine metal tip included
  • Wide cone range per Mayco

Cons

  • Limited color range
  • Thin lines only

Who should skip it: potters who want raised clay lines in their own clay body.

Glazing and firing slip-trailed pots

Let the pot dry slowly, then bisque fire it as usual. Trailed slip can be left bare, covered with a clear glaze to show the lines, or used as raised walls that hold different colored glazes. Ceramic Arts Network notes that slips generally do not run or flatten in the firing, so what you see before firing is largely what you get.

Glaze over raised lines can pool at the base of each line and break thin over the top, which many potters like. Make one test tile per glaze, plus one left unglazed, before glazing a set. If the pot is for food or drink, use a glaze the maker labels for dinnerware, fire it to the stated cone, and test it on your own clay; we cannot promise any glaze is food safe on your pots.

Common slip trailing problems

  • Clogged tip: lumps or grog in the slip, or dried slip in the tip. Screen the slip and clear the tip with a cleaning pin; cap the tip between sessions.
  • Blobs and spits: air in the bottle. Tap out bubbles, keep the bottle full and start each line on scrap clay.
  • Lines spread flat: slip too thin, or the pot too wet. Thicken the slip or wait for the pot to firm up.
  • Cracking or flaking: the pot was too dry, or the slip shrinks differently from the clay. Trail at leather hard, use slip from the same clay and dry slowly under plastic.

Cleanup and safety

Rinse bottles and tips right after use; dried slip is hard to clear. Clay slip contains crystalline silica, and drips that dry on the table or floor become fine dust, so wipe and mop wet and never dry sweep. Wear a NIOSH-approved respirator when mixing dry clay, stains or oxides, and check each product's SDS. Keep slip out of the drain.

What you need

To start slip trailing you need a slip trailer with a couple of tip sizes, a sieve, a lidded jar of slip made from your clay, a banding wheel, a needle tool, a soft brush and plastic for slow drying. Our best pottery tools guide covers the rest of the basic kit.

Sources: Ceramic Arts Network, "Slip Trailing for Beginners"; Pottery Making Illustrated, "Porcelain Slip Trailing"; Meesh Pottery, "Exploring the Art of Slip Trailing in Ceramics"; Xiem Precision Applicator listings at The Ceramic Shop and Hot Clay (tip gauges and openings); The Ceramic Shop listing for the Kemper 4 oz Slip Trail Bottle; Mayco Designer Liner product data. Specs checked November 2026.

Frequently asked questions

How do you prepare slip for slip trailing?

Make slip from the same clay body as the pot, slake dry scraps in water, mix, and screen the slip through a fine sieve to remove lumps and grog. Thicker slip gives raised lines and thinner slip gives flatter lines, so trail test lines on a leather hard slab before decorating a pot.

What can you use as a slip trailer?

Any soft squeeze container with a small opening works: a condiment bottle, an empty glue bottle, a bulb syringe or a purpose-made trailer. Purpose-made trailers with metal needle tips, such as Xiem's Precision Applicator, give the finest and most even lines.

Can you slip trail on bisqueware?

Regular slip does not bond well to bisque, because the fired clay no longer shrinks and the slip does. Use a slip or engobe the maker labels for bisque, or trail underglaze instead, and fire a test tile first.

Can you slip trail with underglaze?

Yes. Underglaze can go in the same bottles, usually with a finer tip than slip, such as 18 gauge. Some makers sell underglaze ready in a squeeze bottle, for example Mayco Designer Liner.

Why is my slip trailing cracking or flaking off?

The usual causes are trailing onto clay that is too dry or using a slip that shrinks differently from the pot. Trail at leather hard, make the slip from the same clay, and dry the piece slowly under loose plastic.

Do you need to glaze over slip trailing?

No. Trailed slip can stay unglazed, take a clear glaze, or hold colored glazes between raised lines. Any surface that touches food or drink should be covered by a glaze the maker labels for dinnerware, fired to its stated cone and tested on your clay.

Researched and written by Muhammad Mustafa

Muhammad Mustafa researches and writes Home Pottery HQ from maker spec sheets, manuals, dealer listings and published studio guidance. He does not claim hands-on testing of products he has not used, and every page names its sources.