Wheel throwing is the process of forming pots on a pottery wheel, and it follows the same order of steps every time: center, open, pull, shape, cut off, dry, trim. This guide walks through each step, gives typical wheel speeds, and explains the problems almost every beginner runs into.
It is research-based: we drew on university ceramics course material (University of the Pacific, Houston Community College), Ceramic Arts Network technique articles and published class outlines. We did not throw pots for this page.
What is wheel throwing?
Throwing clay means using your hands, water and the spin of the wheel to move a lump of clay into a hollow, even-walled form. Your hands stay still while the wheel brings the clay to them. That is why posture and bracing matter so much: any wobble in your hands goes straight into the pot.
Wheel throwing pottery suits round forms such as cylinders, mugs, bowls and vases. It is faster than hand-building once learned, but the first few weeks are mostly practice on centering. If you do not have a wheel yet, our best pottery wheel for beginners guide compares starter options.
Wheel throwing is one method of making pottery, not the whole craft. Pinch, coil and slab work (see hand-building pottery) and slip casting in molds are others, and many potters combine thrown and hand-built parts, such as a slab handle on a thrown mug. The name is old: "throw" comes from the Old English word thrawan, which Etymonline glosses as "to twist, turn," a fitting description of clay shaped as it spins.
Before you sit down
- Clay: soft, smooth stoneware made for throwing, wedged and shaped into balls of about 1 to 2 lb. Small balls are far easier to center. See how to wedge clay.
- Water: a bowl of water and a sponge within easy reach.
- Tools: a needle tool, a wooden knife or modeling tool, a rib, a sponge on a stick if you have one, and a cut-off wire.
- Bats: a bat (a removable disc that pins to the wheelhead) lets you lift a pot off without touching it. Our pottery bats guide explains pin spacing.
- Posture: sit close to the wheel with your elbows braced against your thighs or body. Bracing is what makes your hands steady.
Pottery wheel throwing step by step
The speeds below are general teaching guidance. Houston Community College's seven-step outline, for example, centers and opens at full speed, then pulls and shapes at half speed.
| Step | Typical speed | Goal |
|---|---|---|
| Attach and center | Fast | Clay spins with no wobble |
| Open and compress | Fast to medium | Even, compressed floor |
| Pull walls | Medium to half | Even walls, taller each pull |
| Shape | Half to slow | Final profile |
| Clean up and cut off | Slow to stopped | Clean base, pot free of the bat |
1. Attach the clay
Start with a dry wheelhead or bat. Slap the ball down as close to the middle as you can, then press it firmly down while the wheel turns slowly so it bonds all the way around the base.
2. Center
Wet the clay, brace your elbows, and squeeze it inward and down with steady, equal pressure until it spins without wobbling. Many teachers have beginners cone the clay up and press it back down two or three times first. Centering has its own full guide: how to center clay.
3. Open
Find the exact middle with your thumb or fingers and press straight down. Stop before you reach the wheelhead. Vince Pitelka, writing in Ceramic Arts Network, recommends about 1/4 in of floor for small and medium pots you will not trim, or 3/8 to 1/2 in if you plan to trim a foot. Check by pushing a needle tool down through the floor, pinching it at the clay surface and pulling it out.
Then widen the floor by drawing your fingers out toward you, keeping the bottom flat for a cylinder or curved for a bowl.
4. Compress the base
Run your fingertips or a rib across the floor from the center outward two or three times. Pitelka notes that compressing the bottom helps prevent S-shaped cracks that open in the floor during drying or firing.
5. Pull up the walls
Slow the wheel. Put one hand inside and one outside, with fingertips or a knuckle opposite each other below the wall. Squeeze gently and lift in one slow, steady motion from the base to the rim. Most pots take three pulls or so. Pitelka suggests a wall about 1/2 in thick after the first pull, thinning toward about 1/4 in just below the rim. Press the rim gently with a finger or a piece of chamois after each pull to keep it level.
6. Shape
Push gently from the inside to belly a form out, or squeeze it inward with both hands (collaring) to narrow it. Shape slowly and sparingly. Every pass thins and tires the clay, so do your main shaping on the last pull. A rib held against the outside smooths the surface and firms the wall.
7. Clean up, undercut and cut off
Sponge out any water pooling in the bottom. Use a wooden tool at an angle to trim away the excess clay at the base. Then stop the wheel, hold a cut-off wire tight against the wheelhead or bat and pull it under the pot. If you threw on a bat, lift the whole bat off and set it aside.
8. Dry to leather hard
Let the pot firm up slowly, out of drafts and sun. Cover the rim loosely with plastic if it is drying faster than the base. Our page on leather hard clay explains the stage you are waiting for.
9. Trim (overview)
Trimming removes extra clay from the bottom and carves a foot ring. You turn the leather hard pot upside down, center it on the wheel, secure it with small clay pads, and shave the base with a loop or ribbon tool at slow to medium speed. The question of exactly when a pot is ready to trim is covered in our best pottery trimming tools guide.
Common wheel throwing problems and fixes
The pot collapses
The usual causes are too much water, walls that are uneven or too thin, too many pulls, or a wheel that is spinning too fast for the height of the pot. The University of the Pacific troubleshooting guide lists over-wetting and uneven walls as the main culprits.
- Sponge out water from the inside after every pull.
- Slow the wheel as the pot gets taller.
- Stop at three or four pulls and accept a shorter pot.
The clay keeps going off center
Your elbows are not braced, the pressure from your hands is uneven, or the clay was not wedged well. Re-center before opening; a pot that starts off center does not fix itself.
The walls twist or tear
Twisting comes from pulling too hard or too slowly for the wheel speed, or from dry clay dragging against your fingers. Add a little water or slip and lighten your grip.
Cracks in the bottom
S-cracks usually mean the floor was not compressed or water was left sitting in the bottom. Compress after opening and sponge out water before you cut off.
The clay comes loose from the wheel
The wheelhead or bat was wet when you attached the clay, or the base was not pressed down firmly. Start again on a dry surface.
An uneven rim
With the wheel turning slowly, hold a needle tool steady and level and lower it through the wall just below the low point to cut off a clean ring of clay.
A simple practice routine
Progress comes from repetition, not from keeping every pot. A routine many teachers use looks like this:
- Wedge six to eight balls of the same weight before you sit down, and keep them under plastic.
- Center each ball, open it and pull a plain cylinder. Do not chase fancy shapes yet.
- Cut some practice cylinders straight down the middle with a wire. The cross-section shows exactly where the wall is thick or thin and whether the floor is even, which is the idea behind Pitelka's cross-section article.
- Note what went wrong, wedge the scraps back into your reclaim bucket, and repeat.
Cylinders teach centering, opening and pulling all at once, and nearly every other form starts as one.
Comfort and safety at the wheel
- Protect your back and wrists. University of the Pacific's guide traces wrist strain to poor posture and to working from the wrists alone. Keep your back straight, lean from the hips and let your upper body supply the force.
- Take breaks. Stand up and stretch between pots.
- Tie back long hair and avoid loose sleeves, cords or bracelets near the spinning wheelhead.
- Clean the splash pan wet. Scoop out slop and wipe the pan and floor with a damp sponge before the clay dries into dust. Never pour throwing water down the sink; settle it in a bucket first.
How long does it take to learn wheel throwing?
Expect weeks, not days, before centering feels reliable. Published community class outlines show what a typical beginner course covers: Evergreen Arts' introduction runs six 3-hour sessions covering centering, opening, pulling, shaping, trimming and glazing. A short class like that is the quickest way to get a teacher to correct your hand positions before bad habits set in.
What you need
To practice at home you need a wheel, throwing clay, a basic tool kit and a few bats. Our best pottery wheels guide compares wheels by power, wheelhead size and centering capacity, and our best pottery tools guide covers the starter tools.
Sources: Houston Community College, "7 Steps of Throwing on the Potter's Wheel" (Jason Kishell, Ceramics 1); University of the Pacific Ceramics course text (LibreTexts), "Centering: The Foundation of Wheel Throwing" (Jessica Fong) and "Troubleshooting"; Ceramic Arts Network, "Wheel Throwing in Cross Section" (Vince Pitelka) and "Skilled Centering" (Joyce Michaud); Evergreen Arts, Introduction to Wheel Throwing course listing; JCC Denver beginner wheelthrowing course listing; Etymonline entry for "throw"; Speedball Artista and Clay Boss pages and VEVOR wheel listings (price bands). Specs checked October 2026.